manual story

      New Main Controller

        - Will have the serial number starting with MPMxxxxx.
        - Upgrading the PDL requires a Multi PDL Printer Kit -A2
        - The registration system software name for the firmware is "iR-5000d"
        - A press on the Counter Check key will cause the notation "d" for copier and "dn" for networked printer to be indicated in the lower
           left of the touch panel
        - A press on the Counter Check Key on the control panel will bring up the "Device Config.
        - This will cause various version information to be displayed.
        - Main Board version ( This will give part revision number of the Main controller PCB)
        - Controller Version (MN-CONT / BOOT-ROM / DC-CON)
        - Scanner Version (R-CON / FEEDER)
        - Finisher Version (Sorter/ SDL-STCH)
        - Device Information
        - The Main controller is based on PC133 Standards, the existing memory cannot be used on the new controller.
        - The new main controller only has One Boot Dimm Slot
        - Part Number for the New controller is FG6-7904-000

    Old Main Controller

        - The machine will have serial number starting with NRFxxxxx
        -Multi Printer Board Kit A-1 is used.
        - The registration system software name for the firmware is "iR-5000"
        -The old main controller has 2 Boot Dimm Slots.
        - The old main controller is based on the PC100 standards
        - Part Number for the Old Main Controller is FG6-6531-000

Video Tutorial Ganti Wire Canon IR 5000 series

Jika anda mendapat mesej finsher tidak boleh digunakan , pada canon ir 4570 , ia adalah selamat untuk digunakan, tetapi anda tidak boleh ruji atau sejenis. untuk menghilangkan mesej ini, anda perlu menekan 1 / fungsi tambahan 2 tetapan biasa 3 tatal untuk "LIMITED FUNTION" dan pilih OFF ( OK).
menghidupkan fotokopi off
menghidupkan fotokopi pada ON
Semoga berjaya

อะไรคือสิ่งที่ ย่อย รหัส ?? - E733 - xxxx 0000 - ความพยายาม ใน การสื่อสารกับ เครื่องพิมพ์ ล้มเหลว ที่เริ่มต้นขึ้น 0001 - มี ข้อผิดพลาดใน การสื่อสาร DDI -P คือ 0010 - DDI -P สื่อสาร ข้อผิดพลาด DC ควบคุม ไม่สามารถ ตรวจจับสัญญาณ Vsync แม้หลังจาก ผ่านไป 2 นาที จากการลงทะเบียน เสร็จสมบูรณ์ใน การตั้งค่า การควบคุม มีการ อัปเดต เฟิร์มแว สำหรับ E733 ในระหว่างการส่ง ใน ver.12.04 แฟกซ์ y2006 ตรวจสอบ ในระยะสั้น ตรวจสอบว่า ลากสาย สำหรับ การขนส่ง ในแนวตั้ง เซ็นเซอร์ PS24 มีการ ติดต่อกับ เพลา ลูกกลิ้ง ขนส่ง ที่ก่อให้เกิด แนวตั้ง ฉนวนกันความร้อน ที่จะสวมใส่ ออกและ เครื่อง ทำงานผิดพลาด ซ่อมแซมหรือเปลี่ยน สายรัด สายไฟ

रश्न: कैनन imageRUNNER 6570 फोटोकॉपी के साथ समस्या

त्रुटि कोड E00025-0001 ?
एक: हूपर मोटर बोतल मोटर त्रुटि, माँ बोर्ड में नहीं है, तो (डीसी नियंत्रण फ्यूज असफल )।

finišer ne može kanon koristiti IR 4570 kako riješiti ako ste uzimajući poruku finsher ne može koristiti , na kanonu ir 4570 , to je sigurno koristiti , ali ne možeš sortirano ili vrsta . da biste dobili osloboditi od ove poruke , morate pritisnuti jedan dodatni / 3 funkcije 2 uobičajene postavke i pomaknite se za odabir OFF Limited funkcija ( U redu ) . isključite kopirke kopirka uključivanje sretno

பிழை குறியீடு E808 imageRUNNER 5570 / 6570 சேவை கையேடு பட்டியலில் இல்லை . பிழை குறியீடு விளக்கம் படிக்க வேண்டும்: E808-0001 தி ஐஹெச் மின்சாரம் உள்ளீடு மின்னழுத்தங்கள் நிர்ணயிக்கப்பட்ட மின்னழுத்தங்களை விட அதிகமாக இருக்கும். E808-0002 தி ஐஹெச் மின்சாரம் உள்ளீடு மின்னழுத்தங்கள் நிர்ணயிக்கப்பட்ட மின்னழுத்தங்களை விட குறைவாக இருக்கும் . ஒன்று குறியீடு தீர்வு விளக்கம் சரியான மின்னழுத்தம் கொண்ட ஒரு சுவர் கடையின் ஒரு இயந்திரம் அடைப்பை மற்றும் நிர்ணயம் ஹீட்டர் மின்சாரம் பதிலாக உள்ளது.

Piḻai kuṟiyīṭu E808 imageRUNNER 5570/ 6570 cēvai kaiyēṭu paṭṭiyalil illai. Piḻai kuṟiyīṭu viḷakkam paṭikka vēṇṭum: E808-0001 ti aihec miṉcāram uḷḷīṭu miṉṉaḻuttaṅkaḷ nirṇayikkappaṭṭa miṉṉaḻuttaṅkaḷai viṭa atikamāka irukkum. E808-0002 ti aihec miṉcāram uḷḷīṭu miṉṉaḻuttaṅkaḷ nirṇayikkappaṭṭa miṉṉaḻuttaṅkaḷai viṭa kuṟaivāka irukkum. Oṉṟu kuṟiyīṭu tīrvu viḷakkam cariyāṉa miṉṉaḻuttam koṇṭa oru cuvar kaṭaiyiṉ oru iyantiram aṭaippai maṟṟum nirṇayam hīṭṭar miṉcāram patilāka uḷḷatu.

Q : 캐논 IMAGERUNNER 6570 복사기에 문제가

오류 코드 E00025-0001?

A : 호퍼 모터 병 모터 오류, 마더 보드에없는 경우 (DC 설정 제어 퓨즈 실패).

エラーコードE808は、imageRUNNER連携6570分の5570サービスマニュアルに記載されていません。エラーコードの説明を読んでください。
E808-0001ザIH電源入力電圧が規定の電圧よりも高いです。
E808-0002ザ・IH電源入力電圧が規定電圧よりも低くなっています。
コードのいずれかの治療薬の説明が正しい電圧と壁のコンセントにマシンを接続し、定着ヒータ電源装置を交換することです。

ถ้าคุณได้รับข้อความ finsher ไม่สามารถใช้บน CANON IR 4570 มันมีความปลอดภัยที่จะใช้ แต่คุณไม่สามารถหลักหรือประเภท

เพื่อกำจัดข้อความนี้คุณจะต้องกดอีก 1/2 ฟังก์ชั่นการตั้งค่าที่พบบ่อย 3 เลื่อนไปยังฟังก์ชั่น จำกัด และเลือก OFF (OK)
เปิดเครื่องถ่ายเอกสารออก
เปิดเครื่องถ่ายเอกสารใน

โชคดี

if it happened while using feeder /???
from an old tech pub>
imageRUNNER 5000 / 6000 / 5000i
DADF D1
Title : The error code E315-000D is displayed when the DADF D1 is used. Problem :
The error code E315-000D is displayed when the DADF D1 is used.

Solution :
The error code E315-000D is caused by the Reader Controller not communicating with the DADF Controller, try replacing the Reader Controller to correct the E315-000D error code.
Please note: This may also be caused by a problem with the Hard Drive. Re-loading system software, or replacing the hard drive and re-loading system software may also resolve this problem.

Product applies : imageRUNNER 2270 imageRUNNER 2870 imageRUNNER 3570 imageRUNNER 4570 imageRUNNER 2230 imageRUNNER 2830 imageRUNNER 3530
Title : E520 sub code 8001
Error :The pick up roller will move towards the rear and start to vibrate, then the E520 is generated with the sub code 8001.

Workaround :
Replacing the offset motor resolved the E520 - 8001.

M4 Offset Motor
Part number 4K1-4053-000

Product : imageRUNNER 2270 imageRUNNER 2870 imageRUNNER 3570 imageRUNNER 4570 imageRUNNER 2230 imageRUNNER 2830 imageRUNNER 3530
Title : E520 sub code 8001
Error :The pick up roller will move towards the rear and start to vibrate, then the E520 is generated with the sub code 8001.

Workaround :
Replacing the offset motor resolved the E520 - 8001.

M4 Offset Motor
Part number 4K1-4053-00 - See more at: http://photocopycanon.blogspot.com/2012/02/error-solution-canon-ir4570.html#sthash.F7bsN6Ly.dpuf

What is sub-code ??-E733-xxxx
0000-The attempt at communication with the printer fails at start-up.
0001-There is a DDI-P communication error.
0010-DDI-P communication error DC controller cannot detect Vsync signal even after 2 minutes elapsed from register setting completed in the controller.

there was a firmware update for E733 during fax transmission-in ver.12.04 in y2006

check for short-

Check if the wire harness for the vertical transport sensor PS24 is contacting the vertical transport roller shaft causing the insulation to wear off and the machine to malfunction.
Repair or replace the wire harness.

if fact check all sensor wire harnesses in that area (ex.PS28) also

1) Go into Service Mode by hitting [Additional Functions Key->#2 and 8 Keys together-then>Additional Functions Key]
2) Select [COPIER]
3) Select [FUNCTION] (One of the buttons across the top of the LCD)
4) Select [CLEAR]
5) Scroll to screen two of the LCD using the Right arrow key.
6) Select [PWD-CLR]
7) Hit [OK]
8) Hit the RESET button twice in order to return to the Main LCD Screen. This will turn off the Department ID Management feature on the machine (without deleting the configured Department IDs and Passwords) and will clear out (delete) the System Manager ID and Password.

It might be necessary to Power the unit Off and then Back ON.

If needed

after following above............................................. .
To delete one or more Dept. IDs, follow the steps below:

1. Press Additional Functions from the Control Panel.
2. Select System Settings.
3. Select Dept. ID Management.
4. Select Store Dept ID/password.
5. Select the Dept. ID you want to delete and select Erase.
6. Select Yes to erase the Dept. ID.
7. Click Done 3x to return to the main screen.

NOTE: If you do not know one of the Dept. ID and password, you must know the System Manager ID or you can set one up.
If you do not know the System Manager password either, you then can delete the System Mgr password in service mode.

E355 error code is due to no communication between the Main-Controller board and the Serial Number board below it. The boards are connected by a 11 PIN yellow connector and cable. This yellow connector must be reseated on the new Main-Controller board when changed. The connector must be seated firmly on the board.

When this error occurs, you must go into Service Mode and clear the error code.

How to clear the error code:
1. Enter Service Mode: Press * Additional Functions, 2 and 8 simultaneously, then * Additional Functions again.
2. Then select the [COPIER] option. Under [COPIER], select the Function tab.
3. Under the [FUNCTION] tab, select the [CLEAR] option.
4. In [CLEAR] there is a selection E355-CLR. Select it and hit OK.
5. Reboot the machine.

If the error occurs again:
1. Make sure the connection is secure and tight to the Main-Controller board from the connector cable to the Serial Number board below.
2. Re-seat the Main-Controller board into its slot.
3. Go into service mode and clear the error code as explained above.

* If the error still continues, you probably have a bad Serial Number board and it needs to be replaced.

Is this more likely caused problem by Thermistors,they are built into the fixing film units. To rule out parts, you can replace the fixing film assembly, or the entire fuser.try this and good luck..

The error code E808 is not listed in the imageRUNNER 5570 / 6570 Service Manual. The error code description should read:

E808-0001 The IH power supply input voltages are higher than the stipulated voltages.
E808-0002 The IH power supply input voltages are lower than the stipulated voltages.
The remedy description for either code is to plug the machine into a wall outlet with the correct voltage and replace the fixing heater power supply.

if you are getting a message finsher cannot be used, on canon ir 4570 ,it is safe to use , but you cannot staple or sort.

to get rid of this message ,you have to press 1 additional/functions 2 common settings 3 scroll to LIMITED FUNCTIONS and select OFF (OK).

turn copier off
turn copier on

good luck

my ir7200 produces slant copies when printing copies in a4 orientation...a4r seems to be ok though..i have tried changing separation,feed and pick-up rollers of the pick-up assembly..
paper drawer

i already pin-pointed the problem..i never thought that it is the cassette itself that gives me this trouble..as shown in the figure above,the paper in the cassette is not lifted evenly..that causes the bottom side of the paper to be out first and then drag the rest,which causes the paper to slant...

these are all because of the wire that's lifting the paper is worn-out...this wire is located at the back of the cassette(see figure below)

Q:Problem with Canon IMAGERUNNER 6570 Copier

Error code E00025-0001?

A: Hopper motor bottle motor error,if not in mother board (DC Controll fuse fail ).

manual story

search here..

translate this page

*

Labels

What is the difference between the New iR-5000 Main Controller and the Old iR-5000 Main Controller?

Video Tutorial Ganti Wire IR 5000

finisher tidak boleh menggunakan canon ir 4570 bagaimana untuk menyelesaikan

E733 CANON IR 6570 | เรื่องราว คู่มือ

त्रुटि कोड E00025-0001 CANON IMAGERUNNER 6570 फोटोकॉपी

finišer ne može kanon koristiti IR 4570 kako riješiti

6570 ஐஆர் பிழை குறியீடு e808 நியதி 6570 Ai'ār piḻai kuṟiyīṭu e808 niyati

오류 코드 E00025-0001 캐논 IMAGERUNNER 6570 복사기

오류 코드 E00025-0001?

A : 호퍼 모터 병 모터 오류, 마더 보드에없는 경우 (DC 설정 제어 퓨즈 실패).

エラーコードE808キヤノンIR 6570

หมัดเด็ดที่ไม่สามารถใช้ CANON IR 4570 วิธีการแก้ไข

imageRUNNER 5000 / 6000 / 5000i E315-000D

canon imaggerunner E520 sub code 8001

E733 canon ir 6570 | manual story

how to remove user name password departement id on canon image runner

355-001 on IR5020i | manual story

canon image runner error ir3045 e002

error code e808 canon ir 6570

finisher cannot be use canon ir 4570 how to resolve

canon image runner 7200 slant copy

error code E00025-0001 Canon IMAGERUNNER 6570 Copier

Error code E00025-0001?

A: Hopper motor bottle motor error,if not in mother board (DC Controll fuse fail ).